SLITTING & CUT-TO-LENGTH EQUIPMENT

SPECIFICATIONS:

MFG:  ROWE
Year:  1993

(SOLD) Rowe Uncoiler:  $54,500.00
Model: 50060-DSJ
-Capacity: 50,000# x 60"
-4 Leaf Pumpkin Tooth Mandrel Design
-Hydraulic Wedge Type Mandrel Expansion
-20" - 24" Coil I.D. Range
-Hydraulic Slide Base
-Attached Powered Holddown Roll
  36" W x 10" Dia. Rubber Covered Roll
-Max. Coil O.D.: 72"
-Hydraulic Motor Feed Up Drive w/Air Clutch
-Fawick Air Brake
-Passline: 62" Center Drum to Floor
-Line Direction: Right to Left

Rowe Peeler Table:  $11,500.00
Model PT/HD-60
S/N:  28057
-Capacity: 60" W x 0.250"
-(2) Hydraulic Cylinders for Up / Down Movement
-(1) Hydraulic Cylinder for In / Out Movement of Peeler Blade
Overall Size:  92"L x 74"W x 43"H

Rowe Pinch Rolls:  $10,500.00
-Capacity:  60" x 0.250"
-60" Face x 7" Dia. Rolls
-62.5" Between Housings
-Air Cylinder Loaded
-25 HP DC Motor with Blower
  1750 RPM, 500V
  Less Solid State Drive
-In-Line Gear Reducer
-Passline:  43"
-Overall Size:  157" L x 18" W x 63" High

Rowe Hydraulic Crop Shear:  $24,500.00
-Capacity: 0.250" x 60"
-Entry Driven Pinch Rolls
  66" Face x 5.5" Dia., Rubber Covered
-Straight Blade Design:  64" Long Blade
-Hydraulic Down Cut Via 2 Parker Cylinders
-(2) - 6" Bore Parker Hydraulic Cylinders
-Passline: 40.5"
-Overall Size:  98" L x 48" W x 80" High

Rowe Edge Trimmers:  $11,500.00
-Capacity:  60" x 0.250"
-Double-Stub Design
-64" Max. Width
-Powered Width Adjustment
-Entry Edge Guides on (1) Unit
-Passline:  42"
-Less Drive Motors
-Overall Size:  165" L x 58" W x 52" High
-In Storage:  Toledo, Ohio
-Note:  (2) Units Available, each at below listed price.

(SOLD) Rowe Heavy Duty Straightener:  $32,500.00
Model C15-60
-Capacity: 0.048" - 0.250" Mild Steel
-Entry Side Guides
  Manual Adjustment
-(4) Entry Driven Coil Breaker Rolls
  65" W x 7" Dia.
-(7) Work Rolls, 3 over 4 Design
  65" W x 7" Dia.
-(2) Exit Driven Pinch Rolls
  65" W x 7" Dia.
-Hydraulic Open / Close on Pinch Rolls
-Vertical Adjustment of Work Rolls by 3 HP AC Motor thru Jackscrews
-50 HP DC Drive, Variable Speed
-Line Speed: 35 - 100 FPM
-Overall Dimensions:  Flattener 91" L x 120" W
                      Drive:  108" L x 36" W

(SOLD) Braner High Speed Shear:  $34,500.00
Year: 1998
-For use in Cut-to-Length Line
-Capacity: 0.250" x 72" (Mild Steel)
-75" Long Blade
-Mechanical Downacting
-Motor:  40 HP AC, 1750 RPM
-Air Clutch and Brake
-Raked Blade
-Approx. Overall Size: 154" L x 60" W x 128" High

	REF #: 10221-HK      SERIAL #:      YEAR: 1993


Coil Width:            60"
Coil ID:               20" - 24"
Coil OD:               72"
Gauge Range:           0.048" - 0.250"
Line Direction:        Left to Right

Consisting of the following:

-Peeler Table:
  Model PT/HD-60
  S/N: 28057
  Capacity: 60" W x 0.250"
  (2) Hydraulic Cylinders for Up / Down Movement
  (1) Hydraulic Cylinder for In / Out Movement of Peeler Blade
  Overall Size: 92" L x 74" W x 43" High

-Lee Shaffer Coil End Joiner:
  S/N: 28072
  Capacity:  60" x 0.250"
  Welding Platen:  64" Long
  Weld Clamp Station with Dual Weld Clamp Pads
  Weld Carriage Rides on Precision Screw Shaft
    driven by Vari-Speed DC Motor.
  Exit Passline Roll
  Controls for:
    Left Weld Clamp Open / Close
    Right Hand Weld Clamp Open / Close
    Platen Index Left / Right
    Torch Jog, Fwd / Run
    Weld
    Emergency Stop
    Rheostat for Torch Feed Speed
  Passline:  42"
  Overall Size:  100" L x 60" W x 65" High
  Note: Less Welding Unit

-Scrap Chopper:
  S/N: 28066
  Capacity:  0.250" Mild Steel
  (2) "Sets" of Entry Driven Pinch Rolls
    Each "Set" individually driven by Hydraulic Motors
  Chopper Blades:  (2) 6" L x 2" W x 1.125" Thick Blades per Side
  Approx. 2" Max. Entry Strip Width
  AC Drive Motor
  Overall Size:  40" L x 36" Wide W x 52" High

-Gooseneck Scrap Conveyor:
  S/N: 28070
  11" Wide Conveyor Belt
  AC Motor Driven
  Overall Size:  231" L x 28" W x 74" High

-In Storage:  Toledo, OH







PRICE....................:  SEND A QUOTATION!!!