SLITTING & CUT-TO-LENGTH EQUIPMENT

SPECIFICATIONS:

MATERIAL:                        COLD AND HOT ROLLED STEEL, ALUMINUM
                                 AND STAINLESS STEEL.

SHEAR STRENGTH:                  50,000 PSI - MAXIMUM

MAXIMUM COIL WEIGHT:             50,000 LBS. - ENTRY
                                 50,000 LBS. - EXIT

MAXIMUM COIL WIDTH:              62" ENTRY
                                 60" EXIT

MINIMUM COIL WIDTH:              16" ENTRY

COIL O.D.:                       79" MAXIMUM
                                 35" MINIMUM

COIL I.D.:                       20" TO 24" ENTRY
                                 20" EXIT (24" FUTURE)

MAXIMUM GAUGE:                   .188"

MINIMUM GAUGE:                   .010"

LINE SPEED:                      LOW SPEED RANGE:
                                 COIL BUILD-UP 320 FPM AT 24"
                                 DIAMETER BUILDING UP TO APPROX.
                                 960 FPM ON A 72" O.D. COIL.

                                 HIGH SPEED RANGE:
                                 COIL BUILD-UP 800 FPM AT 24"
                                 DIAMETER BUILDING UP TO APPROX.
                                 1200 FPM ON A 72" O.D. COIL.

                                 HELPER DRIVE SLITTING GEARED IN
                                 AT 800 FPM.

                                 FREE LOOP SLITTING GEARED IN AT 800 
FPM.

HAND OF LINE:                    LEFT TO RIGHT

THE FOLLOWING SLITTER CAPACITIES ARE BASED ON 50,000 PSI SHEAR 
STRENGTH
MATERIAL.  THE NUMBER OF CUTS WILL INCREASE OR DECREASE AS THE SHEAR
STRENGTH DECREASES OR INCREASES.  IF LESSER NUMBER OF CUTS ARE MADE,
THE LINE CAN BE RUN AT HIGHER LINE SPEEDS IN THE COIL BUILD UP MODE.

LOW SPEED RANGE:                6 CUTS IN .188" THICK @ 320 FPM
(PULL THRU AND                  8 CUTS IN .150" THICK @ 320 FPM
 HELPER DRIVE MODES            12 CUTS IN .120" THICK @ 380 FPM
 OF OPERATION)                 16 CUTS IN .090" THICK @ 450 FPM
                               18 CUTS IN .075" THICK @ 600 FPM
                               25 CUTS IN .060" THICK @ 600 FPM
                                AT 960 FPM MAXIMUM IN PULL THRU ONLY.

HIGH SPEED RANGE:               6 CUTS IN .120" THICK @ 800 FPM
(PULL THRU AND HELPER           8 CUTS IN .105" THICK @ 800 FPM
 MODES OF OPERATION)           11 CUTS IN .090" THICK @ 800 FPM
                               16 CUTS IN .075" THICK @ 800 FPM
                               25 CUTS IN .060" THICK @ 900 FPM
                               25 CUTS IN .048" THICK @ 1200 FPM
                               25 CUTS IN .036" THICK @ 1200 FPM

FREE LOOP DRIVE SLITTING:      10 CUTS IN .036" @ 800 FPM
(HIGH SPEED RANGE)             15 CUTS IN .030" @ 800 FPM
                               20 CUTS IN .025" @ 800 FPM
                                (.062" MAXIMUM GAUGE)

ELECTRICITY:                   480 VOLTS (PLUS OR MINUS 10%)
                                3 PHASE, 60 HERTZ
                               500 AMPS AT 480 VOLTS INCOMING POWER

AIR PRESSURE:                  120 PSI REQUIRED, IN A QUANTITY BASED 
ON
                                30 CUBIC FEET OF FREE AIR PER MINUTE,
                                EQUIVALENT TO A 5 HP AIR COMPRESSOR.

NOTE:
THE SPEEDS INDICATED ARE DETERMINED BY THE RECOILER HP REQUIRED TO 
MAKE
THE NUMBER OF CUTS AT THE SPEED INDICATED.
OPERATING CONDITIONS, MATERIAL SHAPE, AND OPERATOR ABILITY MAY AFFECT
MAXIMUM RUNNING SPEED.

CONSISTING OF:

-ENTRY (3) ARM TURNSTILE
  POWERED ROTATION
  C-HOOK TYPE ARMS

-ENTRY COIL CAR
  ABOVE FLOOR TYPE
  SELF-CONTAINED HYDRAULICS

-UNCOILER
  HYDRAULIC EXPANSION
  (4) SEGMENT PUMPKIN TOOTH MANDREL
  POWERED HOLDDOWN ROLL
  AC MOTOR THREADING DRIVE
  WATER COOLED BRAKE
  SLIDING BASE

-PEELER TABLE
  ENTRY PINCH ROLLS
  ENTRY SIDE GUIDES

-SLITTER HEADS
  (2) INJECTOR TYPE HEADS
  7.5" DIA. ARBORS
  SINGLE ECCENTRIC ARBOR ADJUSTMENT
  100 HP DC MOTOR, 850/2550 RPM

-TWO (2) SCRAP WINDERS

-LOOPING PIT TABLE

-TENSION STAND
  COMBINATION PAD AND ROLL TYPE
  ENTRY AND EXIT SEPARATOR TOOLING BARS
  EXIT CROP SHEAR
  EXIT THREADING TABLE TO RECOILER

-RECOILER
  20" DIA. DRUM
  HYDRAULIC CLAMP AND EXPANSION
  HYDRAULIC PUSHOFF
  OVERARM SEPARATOR (ATTACHED TO TENSION STAND)
  (3) SPEED GEARBOX W/20:1, 50:1 AND 1:1 RATIOS
  125 HP DC MOTOR, 850/2550 RPM

-EXIT COIL CAR
  ABOVE FLOOR TYPE
  SELF-CONTAINED HYDRAULICS

-EXIT (3) ARM TURNSTILE
  POWERED ROTATION
  HYDRAULIC PUSHOFF

-MAIN OPERATORS CONTROL PANEL

-COIL DOWNLAYER
  IN-LINE DISCHARGE

-BANDING STATION
  SIGNODE SEMI-AUTOMATIC BANDING HEAD

-STRAIGHT CONVEYOR SECTION

-AUTOMATIC STACKER

-LAZY SUSAN SORT TABLE
  SKID PUSHOFF

-EXIT RUNOUT CONVEYOR

-CONDITION: VERY GOOD

-LINE IS INSTALLED AND UNDER POWER





PRICE....................:  SEND A QUOTATION!!!